Capacity : 3875 gpm (14,667 lpm)
Head : 170 ft (51.8 m)
Submersible Dry Pit
Standard (8VLDP) and Explosion-Proof (8VLXDP)
The 8VLDP and 8VLXDP (Explosion-proof) Submersible Dry Pit Wastewater Pumps are designed especially for high flow applications such as: Large Municipal Stations, Treatment Plants, Transfer Stations and Dewatering. The pump handles solids up to 4 inches in diameter with 3 available motor speeds make it ideal for most high flow wastewater applications.
Advantages By Design
High efficiency hydraulic design cuts pumping costs and extends life of fluid end components.
Head : 170 ft (51.8 m)
Submersible Dry Pit
Standard (8VLDP) and Explosion-Proof (8VLXDP)
The 8VLDP and 8VLXDP (Explosion-proof) Submersible Dry Pit Wastewater Pumps are designed especially for high flow applications such as: Large Municipal Stations, Treatment Plants, Transfer Stations and Dewatering. The pump handles solids up to 4 inches in diameter with 3 available motor speeds make it ideal for most high flow wastewater applications.
Advantages By Design
High efficiency hydraulic design cuts pumping costs and extends life of fluid end components.
- Two-vane, rounded port impeller handles 4" solids with ease at high operating efficiencies.
- High efficiency volute offers quiet operation, low radial loads over extended portion of performance curve.
- Class H Insulation.
- Continuous duty/VFD magnet wire.
- Oil-filled motor and seal cavity for maximum heat dissipation and continuous lubrication.
- Heat sensor thermostats imbedded in windings protect motor from over heat conditions.
- Seal leak probes warn of moisture entry; helps prevent costly motor burn-out.
Unit of Measure
Specifications
Head |
N/A 170 ft51.8 m |
Solids Handling |
N/A 4 in101.6 mm |
Liquids Handling |
N/A Drain Water Effluent Raw Unscreened Sewage |
Intermittent Liquid Temperature |
N/A up to 140 ºFup to 60 ºC |
Winding Insulation Temperature. (Class H) |
N/A 356 ºF180 ºC |
Motor Electrical Data |
N/A
1150 RPM: 30,40,50 HP 230/460/575V, 3Ø, 60 Hz. 1750 RPM: 75,100,125 HP 460/575V 3Ø, 60 Hz. 870 RPM: 15,20,25 HP 200/230/460/575V, 3Ø, 60 Hz |
Acceptable pH Range |
N/A 6 to 9 |
Specific Gravity |
N/A 0.9 to 1.1 |
Viscosity |
N/A 28 to 35 SSU |
Horizontal Discharge |
N/A 8 in203.2 mm |
Speed |
N/A 1150 rpm |
Power |
N/A 30 hp |
Voltage |
N/A 575 V |
Phase |
N/A 3 |
Frequency |
N/A 60 Hz |
Start |
N/A 232 A230 kV·A |
Run |
N/A 35.3 A26.0 kW35.2 kV·A |
NEC Code Letter |
N/A J |
Service Factor |
N/A 42.4 A31.2 kW1.2 |
Capacity |
N/A 3875 gpm14,667 lpm |
Note |
N/A
Consult factory for applications outside of these recommendations FM Class 1, Groups C & D |
Construction Material
Motor Housing Material |
N/A Cast Iron, Class 30, ASTM A48 |
Seal Housing Material |
N/A Cast Iron, Class 30, ASTM A48 |
Volute Case Material |
N/A Cast Iron, Class 30, ASTM A48 |
Cord Cap Material |
N/A Cast Iron, Class 30, ASTM A48 |
Enclosed 2-Vane Impeller Material |
N/A Ductile Iron, Class 65, ASTM A536 |
Power Cord Material |
N/A 25 ft. SOOW |
Control Cord Material |
N/A 25 ft. SOOW |
Standard Double Tandem Mechanical Seal Material |
N/A Carbon & Ceramic, Type 21 |
Optional Double Tandem Mechanical Seal Material |
N/A Lower Tungsten, Carbide |
Pump Shaft Material |
N/A 416 SST |
Motor Shaft Material |
N/A 416 SST |
Fasteners Material |
N/A 300 series SST |
Case Wear Ring Materials |
N/A Bronze |
Base Elbow Material |
N/A Cast Iron, Class 30, ASTM A48 |
- 1 Pending