Myers® 8VLDP and 8VLXDP Series 8" Non-Clog Wastewater Pumps
Myers® Solids Handling Pumps
Capacity : 3875 gpm (14,667 lpm)
Head : 170 ft (51.8 m)
Submersible Dry Pit
Standard (8VLDP) and Explosion-Proof (8VLXDP)
The 8VLDP and 8VLXDP (Explosion-proof) Submersible Dry Pit Wastewater Pumps are designed especially for high flow applications such as: Large Municipal Stations, Treatment Plants, Transfer Stations and Dewatering. The pump handles solids up to 4 inches in diameter with 3 available motor speeds make it ideal for most high flow wastewater applications.
Advantages By Design
High efficiency hydraulic design cuts pumping costs and extends life of fluid end components.
Head : 170 ft (51.8 m)
Submersible Dry Pit
Standard (8VLDP) and Explosion-Proof (8VLXDP)
The 8VLDP and 8VLXDP (Explosion-proof) Submersible Dry Pit Wastewater Pumps are designed especially for high flow applications such as: Large Municipal Stations, Treatment Plants, Transfer Stations and Dewatering. The pump handles solids up to 4 inches in diameter with 3 available motor speeds make it ideal for most high flow wastewater applications.
Advantages By Design
High efficiency hydraulic design cuts pumping costs and extends life of fluid end components.
- Two-vane, rounded port impeller handles 4" solids with ease at high operating efficiencies.
- High efficiency volute offers quiet operation, low radial loads over extended portion of performance curve.
- Class H Insulation.
- Continuous duty/VFD magnet wire.
- Oil-filled motor and seal cavity for maximum heat dissipation and continuous lubrication.
- Heat sensor thermostats imbedded in windings protect motor from over heat conditions.
- Seal leak probes warn of moisture entry; helps prevent costly motor burn-out.
Unit of Measure
Items |
8VLDP150M8-03 Standard 8" Non-Clog Wastewater Pumps |
8VLDP150M8-23 Standard 8" Non-Clog Wastewater Pumps |
8VLDP150M8-43 Standard 8" Non-Clog Wastewater Pumps |
8VLDP150M8-53 Standard 8" Non-Clog Wastewater Pumps |
8VLDP200M8-03 Standard 8" Non-Clog Wastewater Pumps |
|||||
Head | N/A 170 ft51.8 m | |||||||||
Solids Handling | N/A 4 in101.6 mm | |||||||||
Liquids Handling | N/A Drain Water Effluent Raw Unscreened Sewage | |||||||||
Intermittent Liquid Temperature | N/A up to 140 ºFup to 60 ºC | |||||||||
Winding Insulation Temperature. (Class H) | N/A 356 ºF180 ºC | |||||||||
Motor Electrical Data |
N/A
1150 RPM: 30,40,50 HP 230/460/575V, 3Ø, 60 Hz. 1750 RPM: 75,100,125 HP 460/575V 3Ø, 60 Hz. 870 RPM: 15,20,25 HP 200/230/460/575V, 3Ø, 60 Hz |
|||||||||
Acceptable pH Range | N/A 6 to 9 | |||||||||
Specific Gravity | N/A 0.9 to 1.1 | |||||||||
Viscosity | N/A 28 to 35 SSU | |||||||||
Horizontal Discharge | N/A 8 in203.2 mm | |||||||||
Motor Housing Material | N/A Cast Iron, Class 30, ASTM A48 | |||||||||
Seal Housing Material | N/A Cast Iron, Class 30, ASTM A48 | |||||||||
Volute Case Material | N/A Cast Iron, Class 30, ASTM A48 | |||||||||
Cord Cap Material | N/A Cast Iron, Class 30, ASTM A48 | |||||||||
Enclosed 2-Vane Impeller Material | N/A Ductile Iron, Class 65, ASTM A536 | |||||||||
Power Cord Material | N/A 25 ft. SOOW | |||||||||
Control Cord Material | N/A 25 ft. SOOW | |||||||||
Standard Double Tandem Mechanical Seal Material | N/A Carbon & Ceramic, Type 21 | |||||||||
Optional Double Tandem Mechanical Seal Material | N/A Lower Tungsten, Carbide | |||||||||
Pump Shaft Material | N/A 416 SST | |||||||||
Motor Shaft Material | N/A 416 SST | |||||||||
Fasteners Material | N/A 300 series SST | |||||||||
Case Wear Ring Materials | N/A Bronze | |||||||||
Base Elbow Material | N/A Cast Iron, Class 30, ASTM A48 | |||||||||
Speed | N/A 870 rpm | |||||||||
Power | N/A 15 hp | N/A 15 hp | N/A 15 hp | N/A 15 hp | N/A 20 hp | |||||
Voltage | N/A 200 V | N/A 230 V | N/A 460 V | N/A 575 V | N/A 200 V | |||||
Phase | N/A 3 | |||||||||
Frequency | N/A 60 Hz | |||||||||
Start | N/A 334 A116 kV·A | N/A 290 A116 kV·A | N/A 145 A116 kV·A | N/A 116 A116 kV·A | N/A 334 A116 kV·A | |||||
Run | N/A 53.4 A13.4 kW8.5 kV·A | N/A 46.4 A13.4 kW18.5 kV·A | N/A 23.2 A13.4 kW18.5 kV·A | N/A 18.6 A13.4 kW18.5 kV·A | N/A 67.2 A17.6 kW23.2 kV·A | |||||
NEC Code Letter | N/A J | N/A J | N/A J | N/A J | N/A G | |||||
Service Factor | N/A 61.2 A15.8 kW1.2 | N/A 53.2 A15.8 kW1.2 | N/A 26.6 A15.8 kW1.2 | N/A 21.3 A15.8 kW1.2 | N/A 78.5 A20.9 kW1.2 | |||||
Capacity | N/A 3875 gpm14,667 lpm | |||||||||
Agency Approvals1 |
N/A
|
|||||||||
Note | N/A Consult factory for applications outside of these recommendations | |||||||||
|