| Items |
 WGL20-01 Myers® WGL20 Series 2 HP Grinder Pumps |
WGL20-01(LD) Myers® WGL20 Series 2 HP Grinder Pumps |
WGL20-03 Myers® WGL20 Series 2 HP Grinder Pumps |
WGL20-21 Myers® WGL20 Series 2 HP Grinder Pumps |
WGL20-21(LD) Myers® WGL20 Series 2 HP Grinder Pumps |
|||||
| Head | 130 ft40 m | |||||||||
| Liquids Handling | Domestic Raw Sewage | |||||||||
| Intermittent Liquid Temperature | up to 140 ºFup to 60 ºC | |||||||||
| Winding Insulation Temperature. (Class F) | 311 ºF155 ºC | |||||||||
| Motor Electrical Data1 | 1 ph - capacitor start/run. 2 HP, 3450 RPM 200, 230, 460, 575 volts, 60 Hz 208 or 230 volt; 60 Hz 3 ph - induction run | |||||||||
| Acceptable pH Range | 6 to 9 | |||||||||
| Specific Gravity | 0.9 to 1.1 | |||||||||
| Viscosity | 28 to 35 SSU | |||||||||
| Discharge, NPT | 1 1/4 in | |||||||||
| Minimum Sump Diameter (Simplex) | 24 in61 cm | |||||||||
| Minimum Sump Diameter (Duplex) | 36 in91.4 cm | |||||||||
| Motor Housing Material | Cast Iron, Class 30, ASTM A48 | |||||||||
| Seal Housing Material | Cast Iron, Class 30, ASTM A48 | |||||||||
| Volute Case Material | Cast Iron, Class 30, ASTM A48 | |||||||||
| Cord Cap Material | Cast Iron, Class 30, ASTM A48 | |||||||||
| Recessed Impeller Material | Cast Iron, Class 30, ASTM A48 | |||||||||
| Power Cord (with Seal Probe) Material | 15' 14/5 SOOW | |||||||||
| Power Cord (without Seal Probe) Material | 15' 14/4 SOOW | |||||||||
| Standard Double Tandem Mechanical Seal Material | Carbon & Ceramic | |||||||||
| Optional Double Tandem Mechanical Seal Material | Tungsten Carbide | |||||||||
| Pump, Motor Shaft Material | 416 SST | |||||||||
| Fasteners Material | 300 series SST | |||||||||
| Shredding Ring Material | 440 SST, 58-60 Rockwell | |||||||||
| Grinder Impeller Material | 440 SST, 58-60 Rockwell | |||||||||
| Power | 2 hp | |||||||||
| Voltage | 200 V | 200 V | 200 V | 230 V | 230 V | |||||
| Phase | 1 | 1 | 3 | 1 | 1 | |||||
| Frequency | 60 Hz | |||||||||
| Start | 50.0 A10.0 kV·A | 50.0 A10.0 kV·A | 30.0 A10.4 kV·A | 44.0 A10.1 kV·A | 44.0 A10.1 kV·A | |||||
| Run | 15.0 A2.8 kW3.0 kV·A | 15.0 A2.8 kW3.0 kV·A | 9.5 A2.9 kW3.3 kV·A | 12.0 A2.8 kW2.8 kV·A | 12.0 A2.8 kW2.8 kV·A | |||||
| NEC Code Letter | F | |||||||||
| Service Factor | 1.25 | |||||||||
| Capacity | 70 gpm260 lpm | |||||||||
| Agency Approvals2 |
   UL |
|||||||||
| Note |
Consult factory for applications outside of these recommendations. Minimum impeller diameter available is 3 3/4". |
|||||||||
|
||||||||||
