Frequency |
N/A 60 Hz |
Speed |
N/A 890 to 1740 rpm |
Rated Power |
N/A 9 to 134 hp |
Flow Capacity Q max |
N/A 770 to 6,300 gpm |
Head Range |
N/A 8 to 192 ft |
Weight (Pump + Motor) |
N/A 463/2,601 lb |
Installation Type |
N/A Dry Pit Portable Wet Pit |
Internal Oil-Circulation Cooling |
N/A Special Design |
Internal Water Glycol Cooling |
N/A Special Design |
Standard Design, 1 Mech, Shaft Seal + 1 Radial Seal (depending on motor type) |
N/A Standard Design |
Sewage Plant Design, 2 Mech. Shaft Seals (depending on motor type) |
N/A Standard Design |
Temperature Monitoring |
N/A Standard Design |
Ceramics Coating Ceram |
N/A Special Design |
Abrasit Chill Casting |
N/A On Request |
AISI 316 |
N/A On Request |
Duplex |
N/A On Request |
Impellers |
N/A
3393, Single-Channel Impellers 3394, Multi-Channel Impellers 3395, Vortex-Type Impellers 3396, Propeller-Type Impellers |
Sewage Plant Design |
N/A
Low maintenance
|
Sealing Systems |
N/A
Solutions for every application Sewage plant design with WILO Block Seal Mechanical shaft seals of highly wear-resistant silicon-carbide at the motor and pump side integrated in a stainless steel cassette, guarantee - high wear and corrosion resistance - high operation safety - long working life - operation not dependent on the direction of rotation Sewage plant design with double mechanical shaft seal - tandem construction for high stress and difficult applications - 2 mechanical shaft seals of highly wear-resistant silicon-carbide in tandem arrangement. Sewage plant design with double mechanical shaft seal - "Face-to-Face" construction for high stress and difficult applications - 2 mechanical shaft seals in highly wear-resistant arrangement Standard design low-cost sealing for normal applications - pump-side sealing by means of highly wear-resistant mechanical shaft seal of silicon carbide - motor-side sealing by special radial seal |
Safety Components |
N/A
|
Special Designs |
N/A
Special solutions Sewage pumps with mechanical stirring mechanism For clearing sand traps and sludge ponds and for stirring up deposits. The mechanical mixer is attached to a vortex impeller. Sewage pumps with cutting mechanism For pressure drainage of with long discharge pipelines possessing small cross sections. The cutting system before the impeller disintegrates sewage constituents to the required size. Rotor made of Abrasit. Sewage pumps of stainless steel For pumping corrosive media. All parts coming into contact with the media are therefore made of SS 316 stainless steel. With cable protection hose and elastomeres of Viton as a standard. Sewage pump with ceramic coating Ceram C0 - applied in airless procedure. For interior and exterior surfaces in contact with the pumped liquid resistant to salt water and industrial sewage. Layer thickness 400 µm, adhesion 15 N/mm², solvents free. Sewage pumps with cast stainless steel Impeller, sealing flange, pump casing and suction port are made of special material and therefore protected against corrosive or abrasive sewage. Motor with Ceram coating against corrosion, cable with protection hose. |
Special Materials |
N/A
Different combinations Wear-resistant materials and coatings More and more wear-resistant materials and coatings are used in municipal and industrial application fields for pumping abrasive media instead of normal casting materials. These special materials are longer resistant to abrasive attacks due to their specific quality: WILO-liquid ceramics Ceram C1, C2, C3, WILO-Abrasit (Chill casting) Advantages: - very good protection against corrosion (Ceram) - high abrasion-resistance, high wear resistance - resistant to a lot of chemicals, oils, greases, solvents, diluted organic and inorganic acids and leaches (Ceram) - high resistance to corrosive wear, aggressive chemicals and organic solvents (Ceram) In industrial application fields corrosion resistant materials and coatings are required to pump chemically aggressive media. These special materials are very corrosion resistant to acids and bases: WILO-liquid ceramics Ceram C0, C1, C2, C3, AISI 316, duplex further materials on inquiry Advantages: - very good resistance to corrosion by acids and bases - high resistance to inter crystalline corrosion and stress corrosion - excellent stability and tenacity values |
Wet Sump Installation Advantages |
N/A
|
Dry Sump Installation Advantages |
N/A
|
Transportable Installation |
N/A
Application fields
|