Rapid Pump & Meter Service Co., Inc. & Machinery Services Co.
Rapid Pump & Meter Service Co., Inc.
Machinery Services Co.
285 Straight Street
P.O. Box AY
Paterson, NJ, 07509 USA
Fax: 973.345.0301
Phone: 973.345.5600
Email: info@servicer.com
Website: www.rapidservice.com
Print Back

Capacity : 1800 gpm (113.41 L/s)
Head : 165 ft (50.3 m)

Standard (4VC) and Explosion-Proof (4VCX) Construction

The 4VC and 4VCX (Explosion-proof) Submersible Wastewater Pumps are a heavy-duty 4" non-clog series capable of passing a full 3 3/16" spherical solid. Myers rounded port, 2-vane, enclosed impellers prevent solids from binding or clogging and offer high operating efficiencies to cut your pumping costs. The 4VC series modified constant velocity volute case provides smooth operation over an extended portion of the performance curve for longer seal and bearing life. For use in municipal lift stations, treatment plants and industrial waste applications. Myers offers a complete line of wastewater pumps, lift-out rail assemblies, controls and accessories to meet your needs.

Advantages By Design
High efficiency hydraulic design cuts pumping costs and extends life of fluid end components.

  • Two-vane, rounded port, enclosed type impellers handle 3 3/16" solids with ease at high operating efficiencies.
  • Modified constant velocity volute offers quiet operation, low radial loads over extended portion of performance curve.

Durable Motor Will Deliver Many Years Of Reliable Service

  • Oil-filled motor for maximum heat dissipation and constant bearing lubrication.
  • Heat sensor thermostats imbedded in windings protect motor from overheat conditions.
  • Seal leak probes warn of moisture entry; helps prevent costly motor burnout.
  • Double tandem shaft seals prevent sewage from entering motor.
  • Power and control cables are triple sealed with epoxy, compression grommet and terminal board.

Available with optional FM approval for use in Class 1, Groups C and D hazardous locations (4VCX only).
Unit of Measure

Specifications

Head

 N/A 165 ft50.3 m

Solids Handling

 N/A 3 3/16 in80 mm

Liquids Handling

 N/A Effluent Raw Unscreened Sewage Storm Water

Intermittent Liquid Temperature

 N/A up to 140 ºFup to 60 ºC

Winding Insulation Temperature. (Class H)

 N/A 356 ºF180 ºC

Motor Electrical Data

 N/A 1150 RPM: 5–10 HP, 200, 230, 460, 575V, 3Ø, 60 Hz. 1750 RPM: 15 HP, 200, 230, 460, 575V, 3Ø, 60 Hz
20–60 HP, 230, 460, 575V, 3Ø, 60 Hz. 870 RPM: 2–7 1/2 HP, 200, 230, 460, 575V, 3Ø, 60 Hz.

Acceptable pH Range

 N/A 6 to 9

Specific Gravity

 N/A 0.9 to 1.1

Viscosity

 N/A 28 to 35 SSU

Horizontal Discharge Flanged Centerline

 N/A 4 in 125 lb. ANSI 101.6 mm

Speed

 N/A 1150 rpm

Power

 N/A 20 hp

Voltage

 N/A 575 V

Phase

 N/A 3

Frequency

 N/A 60 Hz

Start

 N/A 116 A115.5 kV·A

Run

 N/A 23 A17.2 kW23.0 kV·A

NEC Code Letter

 N/A G

Service Factor

 N/A 28 A21.4 kW1.2

Capacity

 N/A 1800 gpm113.41 L/s

Note

 N/A Consult factory for applications outside of these recommendations.
FM, Class 1, Groups C & D

Construction Material

Motor Housing Material

 N/A Cast Iron, Class 30, ASTM A48

Seal Housing Material

 N/A Cast Iron, Class 30, ASTM A48

Volute Case Material

 N/A Cast Iron, Class 30, ASTM A48

Cord Cap Material

 N/A Cast Iron, Class 30, ASTM A48

Enclosed 2-Vane Impeller Material

 N/A Ductile Iron, Class 65, ASTM A536

Power Cord Material

 N/A 25 ft. SOOW

Control Cord Material

 N/A 25 ft. SOOW

Standard Double Tandem Mechanical Seal Material

 N/A Carbon & Ceramic, Type 21

Optional Double Tandem Mechanical Seal Material

 N/A Lower Tungsten, Carbide

Pump Shaft Material

 N/A 416 SST

Motor Shaft Material

 N/A 416 SST

Fasteners Material

 N/A 300 series SST

Volute Wear Ring Material

 N/A Brass

Agency Approvals

Agency Approvals

 N/A